PCB is also called printed circuit board (PrintedCircuitBoard), it can realize circuit connection and function realization between electronic components, and it is also an important part of power circuit design. Today, I will use this article to introduce high-frequency circuit wiring techniques in PCB design.

　　Multilayer board wiring:

　　 High-frequency circuits tend to have high integration and high wiring density. The use of multilayer boards is not only necessary for wiring, but also an effective means to reduce interference. In the PCBLayout stage, a reasonable choice of printed board size with a certain number of layers can make full use of the intermediate layer to set up the shield, better realize the nearest grounding, and effectively reduce the parasitic inductance and shorten the signal transmission length, while also greatly All of these methods are beneficial to the reliability of high-frequency circuits. With the same material, the noise of the four-layer board is 20dB lower than that of the double-sided board. However, there is also a problem. The higher the number of PCB half-layers, the more complex the manufacturing process, and the higher the unit cost. This requires that in addition to selecting the appropriate number of layers of the PCB board, reasonable Component layout planning, and use correct wiring rules to complete the design.

　　1. The less the lead layer alternate between the pins of high-frequency circuit devices, the better

　　 The so-called “the less the inter-layer alternation of leads, the better” means that the fewer vias (Via) used in the component connection process, the better. One via can bring about 0.5pF distributed capacitance, and reducing the number of vias can significantly increase the speed and reduce the possibility of data errors.

　　2. The shorter the lead between the pins of the high-frequency circuit device, the better

The radiation intensity of the signal is proportional to the length of the signal line. The longer the high-frequency signal lead, the easier it is to couple to the components close to it. Therefore, for signal clock, crystal oscillator, DDR data, LVDS lines, USB lines, HDMI lines and other high-frequency signal lines are required to be as short as possible.

　　3, the lead between the pins of high-speed electronic devices is bent as little as possible

It is best to use a full straight line for the wiring of the high-frequency circuit, and it needs to be turned. It can be turned by a 45-degree broken line or a circular arc. This requirement is only used to improve the fixing strength of the copper foil in the low-frequency circuit. One requirement can reduce the external emission and mutual coupling of high-frequency signals.

　　4. Pay attention to the “crosstalk” introduced by the signal lines in parallel with close distances

　　 High-frequency circuit wiring should pay attention to the “crosstalk” introduced by the close parallel routing of signal lines. Crosstalk refers to the coupling phenomenon between signal lines that are not directly connected. Because high-frequency signals are transmitted in the form of electromagnetic waves along the transmission line, the signal line will act as an antenna, and the energy of the electromagnetic field will be emitted around the transmission line. Undesired noise signals are generated between the signals due to the mutual coupling of electromagnetic fields. Called crosstalk (Crosstalk). The parameters of the PCB layer, the spacing of the signal lines, the electrical characteristics of the driving end and the receiving end, and the signal line termination method all have a certain impact on the crosstalk. Therefore, in order to reduce the crosstalk of high-frequency signals, the following points are required as much as possible when wiring:

　　(1) When the wiring space permits, insert a ground wire or ground plane between the two wires with more serious crosstalk, which can play a role in isolation and reduce crosstalk;

　　(2) When there is a time-varying electromagnetic field in the space surrounding the signal line, if parallel distribution cannot be avoided, a large area of ​​”ground” can be arranged on the opposite side of the parallel signal line to greatly reduce interference;

　　(3) On the premise that the wiring space permits, increase the spacing between adjacent signal lines, reduce the parallel length of the signal lines, and try to make the clock line perpendicular to the key signal line instead of parallel;

　　(4) If parallel routing in the same layer is almost unavoidable, in two adjacent layers, the routing direction must be perpendicular to each other;

　　(5) In digital circuits, the usual clock signals are signals with fast edge changes, which have high external crosstalk. Therefore, in the design, the clock line should be surrounded by a ground wire and more ground wire holes are used to reduce the distributed capacitance, thereby reducing crosstalk;

　　(6) Try to use low-voltage differential clock signals and wrap the ground for high-frequency signal clocks, and pay attention to the integrity of the ground punching;

　　(7) Do not suspend the unused input terminal, but ground it or connect it to the power supply (the power supply is also grounded in the high-frequency signal loop), because the dangling wire may be equivalent to the transmitting antenna, and grounding can inhibit the transmission. Practice has proved that using this method to eliminate crosstalk can sometimes yield immediate results.

　　5. Isolate the ground wire of high-frequency digital signal and analog signal ground wire

　　 When the analog ground wire, digital ground wire, etc. are connected to the public ground wire, use high-frequency choke magnetic beads to connect or directly isolate and select a suitable place for single-point interconnection. The ground potential of the ground wire of the high-frequency digital signal is generally inconsistent, and there is often a certain voltage difference between the two directly. Moreover, the ground wire of the high-frequency digital signal often contains very rich harmonic components of the high-frequency signal. When the digital signal ground wire and the analog signal ground wire are directly connected, the harmonics of the high-frequency signal will interfere with the analog signal through the ground wire coupling. Therefore, under normal circumstances, the ground wire of the high-frequency digital signal and the ground wire of the analog signal are to be isolated, and a single-point interconnection method can be adopted at a suitable position, or a method of high-frequency choke magnetic beads interconnection can be used.

　　6. ​​Add high-frequency decoupling capacitor to the power supply pin of the integrated circuit block

　　 Add a high-frequency decoupling capacitor to the power pin of each integrated circuit block. Increasing the high-frequency decoupling capacitor of the power supply pin can effectively suppress the interference of high-frequency harmonics on the power supply pin.

　　 7. Avoid loops formed by wiring

　　 Various high-frequency signal traces should not form loops as much as possible. If it is unavoidable, the loop area should be as small as possible.

　　 8. Good signal impedance matching must be guaranteed

　　 In the process of signal transmission, when the impedance does not match, the signal will be reflected in the transmission channel. The reflection will cause the synthesized signal to form an overshoot, causing the signal to fluctuate near the logic threshold.

　　 The fundamental way to eliminate reflection is to make the impedance of the transmission signal well matched. Since the greater the difference between the load impedance and the characteristic impedance of the transmission line, the greater the reflection, so the characteristic impedance of the signal transmission line should be as equal as possible to the load impedance. At the same time, note that the transmission line on the PCB must not have sudden changes or corners, and try to keep the impedance of each point of the transmission line continuous, otherwise there will be reflections between the segments of the transmission line. This requires that during high-speed PCB wiring, the following wiring rules must be observed:

　　 (1) LVDS wiring rules. Requires LVDS signal differential routing, line width 7mil, line spacing 6mil, the purpose is to control the differential signal impedance of HDMI to 100+-15% ohm;

　　 (2) USB wiring rules. Requires USB signal differential routing, line width 10mil, line spacing 6mil, ground line and signal line spacing 6mil;

　　(3) HDMI wiring rules. HDMI signal differential routing is required, the line width is 10mil, the line spacing is 6mil, and the spacing between each two sets of HDMI differential signal pairs exceeds 20mil;

　　(4) DDR wiring rules. DDR1 traces require signals not to go through holes as much as possible, signal lines are of equal width, and lines are equally spaced. The trace must meet the 2W principle to reduce crosstalk between signals. For high-speed devices of DDR2 and above, high-frequency data is also required. The lines are equal in length to ensure the impedance matching of the signal.

　　Maintain the integrity of signal transmission and prevent the “ground bounce phenomenon” caused by ground splitting.